Aditya Patel

First, take an LED and connect it to the breadboard. Then, connect the LDR sensor to the breadboard. Use jumper wires to connect the breadboard components to the Arduino. Finally, open the Arduino IDE, enter the required code, and upload the code to the Arduino.

I take an LDR (Light Dependent Resistor) and connect it to the breadboard. Then, I use jumper wires to connect the LDR and breadboard to the Arduino. Finally, I enter the code into the Arduino IDE and upload it to the Arduino.

I take five LEDs and attach them to the breadboard. Then, I use jumper wires to connect the Arduino to the breadboard. Next, I connect a push button to the breadboard. Finally, I use a USB cable to connect the Arduino to the computer and enter the code into the Arduino IDE

I am take 3 Potentiometers and attach the breadboard and take jumper wire and attach breadboard to Arduino. I am bring a USB cable and joint with Arduino and enter the code and Led is blinking.

I am take a 4 LED and joint on breadboard and take a Potentiometer and joint the breadboard. I am take jumper wire and joint breadboard to Arduino. I am take a USB cable a connect into the Arduino and I am enter the code.

I am take a Potentiometer and attach the breadboard. Jumper wire attach the breadboard to Arduino and use a USB cable and enter the code.

I am attach the jumper wire, Potentiometer, LED etc. attach the this are things on breadboard. Jumper wire attach breadboard to Arduino. Take a USB cable and connect the Arduino to Laptop and Enter the code. I am learn Potentiometer.

I am take a Potentiometer attach with breadboard and take jumper wire attach the breadboard to Arduino and Arduino connect the USB cable and enter the code.

First I am take a buzzer and attach the breadboard. Take a push button and attach the breadboard and take jumper wire and attach the breadboard to Arduino. Take a USB cable and joint the Arduino. Final enter the code.

First take a LED and attach the breadboard. Take a push button and attach the breadboard. Take a jumper wire and attach the breadboard.

I am take a push Button.Take a jumper wires. Push button attach the breadboard. Jumper wires attach the breadboard. All things attach the Arduino and take USB cable and joint the Arduino.

I am take one LED and attach the breadboard and the GND attach the short leg and 5V attach the long leg.

I am put LED and connect to breadboard. Use jumper wire to attach breadboard to Arduino. Use a USB cable and enter the code and my project is working.

I am take breadboard and jumper wire attach and LED attach breadboard.Jumper wire connect the Arduino.Enter the code

I am bring jumper wire,Arduino,breadboard,LED,USB cable.First jumper wire take and attach with Arduino to breadboard.Take LED and attach with breadboard.put a USB cable and connect to Arduino and take a code and an enter the code.

I am take 6 LED and jumper wire. First take a one breadboard and Arduino. bring a LED and connect to breadboard. Bring jumper wires and attach with Arduino to breadboard. Take a USB cable and connect Laptop to Arduino. Enter the code.

I am take a 6 LED and jumper wires. first take a breadboard and All LED attach with breadboard and jumper wires.jumpre wires connect to a Arduino.like this photo. Use a USB cable and attach to a Arduino and enter code and your LED is blinking.

I am take a 4 LED and jumper wire first take a breadboard.breadboard put on the table and all LED attach with breadboard.All jumper wire take and connect to the LED line and jumper wire connect to Arduino. use a USB cable to connect laptop to Arduino. Enter your code.

I am take a 8 LED. Attach with breadboard.use jumper wire and and jumper wire connect to breadboard to Arduino.and more conation.your LED is working and add code.

take a 4 LED and connect with breadboard. and conation with Arduino.

take a 3 LED. 4 jumper wires. attach the LED in breadboard and jumper wires connect to Arduino.

first is I am take a 2 LED and take jumper and joint with LED line side.jumper wire attach with Arduino and bring a code and put to Arduino.

fist I am bring a code and paste the Arduino. I am take 2 jumper wire and attach with Arduino.

I am take 2 LED AND 2 JUMPER WIRES and one jumper wire attach with GND to breadboard and 2nd jumper wire attach with 13 to breadboard.

fist bring a code and use a code software and put code to Arduino and take a 2 jumper wires and attach with Arduino.

connect the Arduino and write a code and use a Arduino IDE code software and take 2 LED and take 2 jumper wires and attach with Arduino to breadboard and your LED is slowly blinking.

take 8 LED and attach the breadbord and use jumper wires and CONNECT with Lepto and the leptop to use USB cable.

first take a 5 LED and attach the breadboard and connect with Ardiuno and take a USB cable and joint with leptop.

I am take 4 LED and lint braedbord and 2 wires take and joint with Ardiuno. Use USB[Unive Serel Bus] cable and connect to Leptop

first take 2 LED and joint with breadboard and joint with Arduino and connect with Leptop and use USB cable.

first I am take jumper wires and first wire joint into GND and 2nd wire joint into 13 and 2 wires joint into a line and take LED and joint into a line infrount of the wires

I am use ardiuno and usb cable and led. first i am take a led and fit on short wire in GND and long wire in 13.